Description
The new GKTECH suspension arms are built to a high standard and are far from the generic garbage that most people are used to but at very reasonable prices. They are CAD designed, FEA tested, have forged and then CNC machined ends, they're mandrel bent (toe arms, caster rods and LCA's), CNC tube notched (camber and LCA's) and TIG welded and to finish the arms off they're E-coated (aka electrophoresis coating) for rust prevention and we're exclusively using high quality Teflon lined bearings (over $140 in bearings cost for the pair on their own)
Our rear lower control arms allow for + or - 15mm's of track width via a basic shim style system without having REIB (rod ends in bending). Wider track for FR cars gives more grip and less body roll and by adjusting the rear LCA's you can alter a vehicles understeer/oversteer properties.
- Feature 5/8" Teflon lined sphericals (inner) and high mis-alignment 3/4 sphericals (outer) which eliminates the flex found in factory rubber bushing offering a more direct and predictable feel.
- V3 arms are manufactured from chromoly 28mm OD (3mm wall) tube with CNC machined ends with recessed ends for additional strength.
- CAD designed, FEA tested, CNC machined ends, CNC mandrel bent arms (toe arms, caster rods and LCA's), CNC tube notched (camber and LCA's) and TIG welded
NOTE: If you are intending on running the rear LCA's any wider than 10mm's over factory it is recommended that you run axle spacers as seen here: http://www.gktech.com/products/#43
Vehicle Compatibility:
- Nissan 180sx
- Nissan S13 Silvia
- Nissan S14 200SX
- Nissan S15 200SX
- Nissan Skyline R32 GTS-T
- Nissan Skyline R32 GTR
- Nissan Skyline R33 GTS-T
- Nissan Skyline R33 GTR
- Nissan Skyline R34 GTT
- Nissan Skyline R34 GTR
- Nissan C33
- Nissan C34
- Nissan C35
- Nissan A31 Cefiro
- Nissan Z32 300zx
Our rear lower control arms allow for + or - 15mm's of track width via a basic shim style system without having REIB (rod ends in bending). Wider track for FR cars gives more grip and less body roll and by adjusting the rear LCA's you can alter a vehicles understeer/oversteer properties.
- Feature 5/8" Teflon lined sphericals (inner) and high mis-alignment 3/4 sphericals (outer) which eliminates the flex found in factory rubber bushing offering a more direct and predictable feel.
- V3 arms are manufactured from chromoly 28mm OD (3mm wall) tube with CNC machined ends with recessed ends for additional strength.
- CAD designed, FEA tested, CNC machined ends, CNC mandrel bent arms (toe arms, caster rods and LCA's), CNC tube notched (camber and LCA's) and TIG welded
NOTE: If you are intending on running the rear LCA's any wider than 10mm's over factory it is recommended that you run axle spacers as seen here: http://www.gktech.com/products/#43
Vehicle Compatibility:
- Nissan 180sx
- Nissan S13 Silvia
- Nissan S14 200SX
- Nissan S15 200SX
- Nissan Skyline R32 GTS-T
- Nissan Skyline R32 GTR
- Nissan Skyline R33 GTS-T
- Nissan Skyline R33 GTR
- Nissan Skyline R34 GTT
- Nissan Skyline R34 GTR
- Nissan C33
- Nissan C34
- Nissan C35
- Nissan A31 Cefiro
- Nissan Z32 300zx
